Amperage: |
- 10 Amp power supply
|
Power Supply
2-679-0995: |
- UL Listed Sub-Assembly power supply/charger converts a 120VAC, 60Hz input
into a single 24VDC output
|
Power Supply:
2-679-0996:
|
- UL Listed Sub-Assembly power supply/charger converts a 120VAC, 60Hz input
into a single 12VDC output |
Power Supply:
2-679-0995 &
2-679-0996
|
- Fire alarm disconnect
- Overvoltage protection
- Low power disconnect (prevents deep discharge of stand-by batteries) |
Dual Input Power
Distribution Module
2-679-1100: |
- Designed to steer the power from either two (2) low voltage AC or DC
power sources
- Power is distributed over a total of eight (8) fused protected outputs
|
Access Power Controller
2-679-0997: |
- Converts one (1) 12 to 24 VAC or VDC input into four (4) independently
controlled fuse protected outputs
- Power outputs can be converted to dry form “C” contacts
- Outputs are activated by an open collector sink or normally open
(NO) dry trigger input from an Access Control System, Card Reader,
Keypad, Push Button, PIR, etc., and will route power to a variety of
access control hardware devices including Mag Locks, Electric
Strikes, Magnetic Door Holders, etc.
- Outputs will operate both in Fail-Safe or Fail-Secure modes
- Designed to be powered by one common power source which will provide
power for both the board operation and locking devices, or two (2) totally
independent power sources, one (1) providing power for board operation
and the other for lock/accessory power
- FACP Interface enables Emergency Egress, Alarm Monitoring, or may be
used to trigger other auxiliary devices. The fire alarm disconnect
feature is individually selected for any or all of the four (4) outputs
|
Access Power Controller
2-679-0998:
|
- Converts one (1) 12 to 24 VAC or VDC input into eight (8) independently
controlled fuse protected outputs
- Power outputs can be converted to dry form “C” contacts
- Outputs are activated by an open collector sink or normally open
(NO) dry trigger input from an Access Control System, Card Reader,
Keypad, Push Button, PIR, etc., and will route power to a variety of
access control hardware devices including Mag Locks, Electric
Strikes, Magnetic Door Holders, etc.
- Outputs will operate both in Fail-Safe or Fail-Secure modes
- Designed to be powered by one common power source which will provide
power for both the board operation and locking devices, or two (2) totally
independent power sources, one (1) providing power for board operation
and the other for lock/accessory power
- FACP Interface enables Emergency Egress, Alarm Monitoring, or may be
used to trigger other auxiliary devices. The fire alarm disconnect
feature is individually selected for any or all of the four (4) outputs
|
Enclosure & Environmental: |
- Wall mount for indoor use
- Operating temperature: 32°F to 120°F
- Storage temperature: -4°F to 158°F
- 16 AWB powder-coated steel enclosure
- Single 2" center knockout on the top of the enclosure
- Sixteen (16) two-stage knockouts for 0.75" or 1" conduit
- 21.5" (W) x 27.25" (H) x 6.5" (D)
- Approximate weight: 37.1 lbs.
|
Included Contents: |
- Enclosure
- Power supply
- Voltage regulator
- Dual input power distribution module
- Access power controller
- Removable mounting backplane
- One (1) cam lock
- One (1) Tamper switch
- Mounting hardware
|
Certifications: |
- CE approved
- UL294 Listed - Access Control System Units
|
Warranty: |
- One (1) year
|
Notes: |
- Control Units not included. |
|
|