Tiny Houses

Affordable housing is drifting further out of reach, especially for people who have had to face many challenges. Enter Dianne Marshak with Social Justice 4 All. Social Justice 4 All, a group of Catholics and other Christians from West St. Louis County, had been looking for a project to help people who were homeless transition off the streets.  This coming after a trip to Chicago where Dianne encountered several people who were homeless and was moved to do something to help.

Social Justice 4 All learned about the Solomon Project, a 12-year-old project to provide affordable housing in north St. Louis, from the North Grand Neighborhood Services (NGNS). During a panel discussion on homelessness, it was suggested that tiny homes could help people transition out of homelessness. As the discussion continued a teacher from Rockwood Summit High School (website) volunteered his students to build the houses. The Tiny Houses Project was born and a commitment of three tiny homes, measuring 14′ x 26′, was made.

Hager’s involvement began when a former employee now retired, reached out with an appeal for a donation of the door hardware for the exterior doors on each tiny home.  The Hager family, without hesitation, said yes. With Johnston Hager, VP of Residential Sales and National Accounts, as Hager’s point person our internal residential customer service expert, Angelia McGraw, worked with Dianne to make sure the door hardware fit the preps on the doors that the students at Rockwood Summit High School had built.

Today, there are two tiny houses on permanent foundations in the City of St. Louis. Interiors are being worked on and both homes are expected to be ready for occupancy later this year. Once both of these homes are ready for new residents the third tiny house will be built on site.

Hager Companies was honored to participate in this worthwhile project. For more information, or if you’d like to get involved, check out Social Justice 4 All’s website here.

We were touched when Dianne Marshak came by the office to present Johnston with a plaque thanking Hager Companies for the door hardware donation. The plaque was made by the students at Rockwood Summit High School, which made it exceptionally special. We were happy to play a part, along with many other companies and individuals, in providing tiny homes for people who just need a hand.

Dianne Marshak with Social Justice 4 All and Johnston Hager
RSS Feed

Latch Protectors

Being a door hardware manufacturer we are passionate about security. Keeping a door shut and locked plays an important role in keeping people safe. When you hear “security” you may be envisioning a lot of different equipment like cameras, card readers, and maybe even grilles over doors and windows. Hager offers several levels of door hardware security options, but depending on your facility some simple, first steps, may be a better choice.

In the photos below you’ll notice a metal plate that runs vertically along the seam of the pair of doors, by the lockset. This metal plate is called a latch protector and they are available in a wide range of sizes, finishes, and shapes so they can be installed or retrofitted to most locks on both single and pairs of doors.

While we don’t recommend this application, we appreciate the effort of the building owner to resolve a security issue on an existing pair of doors.

This piece of hardware is designed to deter forced entry through door prying, kick-ins, and other actions to gain unauthorized access. Latch protectors provide simple protection from break-ins that is easy to install and is a low-cost first step in a line of defense.  Door openings where latch protectors may be useful include exterior entry, storage, equipment, or any opening where you need a little extra bit of security.

For more information about our latch protection products or any of our many other security products please contact your local sales representative or our customer service department at 800-255-3590.

 

RSS Feed

How to Size a Push Bar

We’ve all heard the adage “measure twice, cut once”. This definitely applies when prepping doors for hardware. And, how to order certain door hardware for doors, like push bars.

We have several helpful documents on our website and How to Size a Push Bar is one of them. This document can be found under the Related Files tab on all our push bar product web pages.

Here are a few tips –

For a Flush Door

To determine the size of a bent end bar with bracket take the door width minus 5″ and that will equal the correct push bar length.

More …

RSS Feed

The Lowdown on Low-Energy Power Operators by Gordon Holmes

This article appears in the February issue of the DHI Security + Safety Magazine and is reprinted here with their permission.

Specifying door hardware can sometimes feel like a juggling act. Securing the building is often the first thought when considering door hardware. Determining who will have access to what areas and when can be confounding. On top of building and user requirements specifiers must also consider ADA laws, fire and life safety codes that dictate the types of hardware and how they are installed. Depending on the door opening several codes can interplay, and the door hardware must comply with every code and law.

Low-energy power operators have been designed with a few of these specific requirements in mind in order to provide easier accessibility through doorways. Functioning on the same principle as a door closer that controls the opening and closing of a door, “low-energy” refers only to the speed at which the door opens and closes. Low energy operators require a “knowing act. To open the door a person would need to push a button or pull on a handle, which engages control over the door.

The 2013 Builders Hardware Manufacturers Association (BHMA) Standard ANSI/BHMA A156.19 – American National Standard for Power Assist and Low Energy Power Operator Doors define a “knowing act” as follows:

“Consciously initiating the powered opening of a low-energy power door using acceptable methods including: wall or jamb-mounted contact switches such as push plates; fixed non-contact switches; the action of manual opening (pushing or pulling) a door; and controlled access devices such as keypads, card readers, and key switches.”

More …

RSS Feed

New Accessories for the Roton® Continuous Geared Hinge Product Line

In keeping with our promise to provide products that enhance the safety and security of our customers, Hager Companies announces the new TIPIT® and the newly designed Hospital Tip for our Roton® Continuous Hinge product line.

TIPIT®
This product was designed specifically with safety in mind. When door openings are fitted with the patented TIPIT® in conjunction with our Roton Continuous Geared Hinge, this combination provides a safe environment while meeting institutional requirements for preventing objects from being hung from the top of the hinge.

Made from durable, high-tech polymer the TIPIT® securely fastens to the door frame header using the included #10 TORX® SST security screws. Offered in two models, Concealed and Full Surface and two finished, Gray and Black. Suitable for both retrofit and new construction applications in the following vertical markets: Hospitals, Correctional facilities, Schools, Rehabilitation centers, and other institutions.

More …

RSS Feed

Project Profile – The Sheridan at Laumeier Park

An assisted living and memory care facility, the Sheridan features 43 assisted-living apartments plus 41 memory care residences. An upscale community that sits on 3.9 acres and has nearly 69,000 square feet of finished space.

Working with the warm tones of the design the door hardware was supplied with a dark bronze finish. The 4500 Series vertical rod exit devices were provided less bottom rod to avoid tripping hazards. Furnished with the August lever style that meets ADA ANSI A117.1 requirements and provides a continuous look throughout the project, the entry suite doors utilized 3800 Series mortise locks and the interior doors the 3600 Series locks. Both provided the necessary security and dependability of a commercial lock with a more residential look.

More …

RSS Feed

Concave vs. Convex Wall Stops

Wall and floor stops are inexpensive products that, when installed correctly, can help prevent damage to a wall, lockset or door. If a door is forcefully pushed open, a stop is meant to protect the wall from being gouged by the door or lockset, and it will also protect the door hardware from being damaged by a quick meeting with the wall.

 

Wall and floor stops come in a wide variety of shapes and sizes and can be mounted on the wall or on the floor behind the door.  For this post, we are going to focus on concave and convex wall stops.

More …

RSS Feed

Everything You’ve Always Wanted to Know About Door Closers by Vince Butler

This article appears in the January issue of the DHI Security + Safety Magazine and is reprinted here with their permission.

Everything You’ve Always Wanted to Know About Door Closers by Vince Butler

Door closers – if you’ll pardon the pun – literally go over most people’s heads. They are usually installed at the top of doors and door frames, out of the line of sight, unnoticed. Most door closers are purposely designed to match the door and frame so they don’t attract attention.

More …

RSS Feed

Team Member Profile – Sheryl Simon, CSI, CDT – Manager, Architectural Specification Consultants

Sheryl Simon has been with Hager Companies for 13 years and was recently promoted to Manager, Architectural Specifications Consultants. We sat down with Sheryl to ask her a few questions.

Sheryl Simon at one of the many CSI STL events she volunteers for. Sheryl currently is 2nd VP for the chapter. Photo credit: George Everding

Childhood AmbitionI was always interested in design. (I’m not sure if it’s an ambition or an obsession.) Even as a young child I was always re-arranging the furniture. My parents never knew what to expect when they came home. 

First JobWorking at a very busy ice cream stand. The lines seemed to never end but it was fun interacting with all the customers. 

What led you to the hardware industry: I married into it and very quickly became a hardware geek. 

Proudest professional momentWhen I passed my CDT. It is a very difficult exam and required a lot of studying. 

More …

RSS Feed
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. ...
  9. 17